Battery powered Headphone Amplifier

Low distortion Class-B circuitry 6V Battery Supply

Some lovers of High Fidelity headphone listening prefer the use of battery powered headphone amplifiers, not only for portable units but also for home "table" applications. This design is intended to fulfil their needs and its topology is derived from the Portable Headphone Amplifier featuring an NPN/PNP compound pair emitter follower output stage. 

An improved output driving capability is gained by making this a push-pull Class-B arrangement. Output power can reach 100mW RMS into a 16 Ohm load at 6V supply with low standing and mean current consumption, allowing long battery duration. The single voltage gain stage allows the easy implementation of a shunt-feedback circuitry giving excellent frequency stability.
.

Circuit diagram :

Battery-powered Headphone Amplifier Circuit diagram

Notes:

• For a Stereo version of this circuit, all parts must be doubled except P1, SW1, J2 and B1.
• Before setting quiescent current rotate the volume control P1 to the minimum, Trimmer R6 to maximum resistance and Trimmer R3 to about the middle of its travel.
• Connect a suitable headphone set or, better, a 33 Ohm 1/2W resistor to the amplifier output.
• Switch on the supply and measure the battery voltage with a Multimeter set to about 10Vdc fsd.
• Connect the Multimeter across the positive end of C4 and the negative ground.
• Rotate R3 in order to read on the Multimeter display exactly half of the battery voltage previously measured.
• Switch off the supply, disconnect the Multimeter and reconnect it, set to measure about 10mA fsd, in series to the positive supply of the amplifier.
• Switch on the supply and rotate R6 slowly until a reading of about 3mA is displayed.
• Check again the voltage at the positive end of C4 and readjust R3 if necessary.
• Wait about 15 minutes, watch if the current is varying and readjust if necessary.
• Those lucky enough to reach an oscilloscope and a 1KHz sine wave generator, can drive the amplifier to the maximum output power and adjust R3 in order to obtain a symmetrical clipping of the sine wave displayed.

Technical data:

Output power (1KHz sinewave):
    16 Ohm: 100mW RMS
    32 Ohm: 60mW RMS
    64 Ohm: 35mW RMS
    100 Ohm: 22.5mW RMS
    300 Ohm: 8.5mW RMS
Sensitivity:
    160mV input for 1V RMS output into 32 Ohm load (31mW)
    200mV input for 1.27V RMS output into 32 Ohm load (50mW)
Frequency response @ 1V RMS:
    flat from 45Hz to 20KHz, -1dB @ 35Hz, -2dB @ 24Hz
Total harmonic distortion into 16 Ohm load @ 1KHz:
    1V RMS (62mW) 0.015% 1.27V RMS (onset of clipping, 100mW) 0.04%
Total harmonic distortion into 16 Ohm load @ 10KHz:
    1V RMS (62mW) 0.05% 1.27V RMS (onset of clipping, 100mW) 0.1%
Unconditionally stable on capacitive loads

Source : red circuits

Read more

Battery powered Night Lamp Circuit

Ultra-low current drawing 1.5V battery supply

This circuit is usable as a Night Lamp when a wall mains socket is not available to plug-in an ever running small neon lamp device. In order to ensure minimum battery consumption, one 1.5V cell is used, and a simple voltage doubler drives a pulsating ultra-bright LED: current drawing is less than 500µA.
An optional Photo resistor will switch-off the circuit in daylight or when room lamps illuminate, allowing further current economy.

This device will run for about 3 months continuously on an ordinary AA sized cell or for around 6 months on an alkaline type cell but, adding the Photo resistor circuitry, running time will be doubled or, very likely, triplicated.

Circuit diagram :

 Battery-powered Night Lamp Circuit diagram

Parts:

R1,R2___________1M   1/4W Resistors
R3_____________47K   1/4W Resistor (optional: see Notes)
R4____________Photo resistor (any type, optional: see Notes)

C1____________100nF  63V Polyester Capacitor
C2____________220µF  25V Electrolytic Capacitor

D1______________LED  Red 10mm. Ultra-bright (see Notes)
D2___________1N5819  40V 1A Schottky-barrier Diode (see Notes)

IC1____________7555 or TS555CN CMos Timer IC

B1_____________1.5V Battery (AA or AAA cell etc.)

Circuit operation:

IC1 generates a square wave at about 4Hz frequency. C2 & D2 form a voltage doubler, necessary to raise the battery voltage to a peak value able to drive the LED.

Notes:

• IC1 must be a CMos type: only these devices can safely operate at 1.5V supply or less.
• If you are not needing Photo resistor operation, omit R3 & R4 and connect pin 4 of IC1 to positive supply.
• Ordinary LEDs can be used, but light intensity will be poor.
• An ordinary 1N4148 type diode can be used instead of the 1N5819 Schottky-barrier type diode, but LED intensity will be reduced due to the higher voltage drop.
• Any Schottky-barrier type diode can be used in place of the 1N5819, e.g. the BAT46, rated @ 100V 150mA.

Source :http://www.ecircuitslab.com

Read more

Simpled Solar Powered Lithium Ion Battery Charger Circuit

The circuit below feeds a controlled current and voltage to a 3.6v lithium ion battery. The current is limited to 300ma and the voltage is limited to 4.2 volts. The circuit uses a LTC1734 IC from Linear Technology. No diode is needed between the circuit and a 6 volt solar panel. Some very nice 6 volt solar panels are available from www.plastecs.comTheir SP6-200-12 cranks out about 1 watt while the SP6-300-12 can produce about 2 watts. Assuming a 6 hour sunlit day, the 2 watt panel will pump about 1.8 amp-hours into a battery.

Read more